Toyota SPA34 Manuale delle Istruzioni

SP20 Series• Read this manual carefully before use and always follow the instructions.• Keep the manual in a convenient place for easy reference.• If

10• How to use handwheelAlways turn the handwheel towards yourself. (in the direction of the arrow, forwards)Note: If you turn it in the reverse dire

11Before use• Using the presser foot pressure adjustment knobÚ Equipped only with model XXX34By turning the presser foot pressure adjustment knob at

12• How to use quick adviserThis quick adviser describes basic countermeasures about the main troubles.Meaning of the illustrationsIllustrations of th

13Prepare the foot controller.Insert the power cord connector into the terminal box.Insert the power plug into the outlet.The power is turned on.123•

14• Installation of battery for winding the lower thread31Open the battery holder cover in the direction of the arrow.2Install the battery while confi

15• Winding the lower threadUse a TOYOTA-exclusive bobbin.The exclusive motor driven by a battery winds the lower thread.13Pull the thread from the th

16674From the inside, pass the thread end through the hole in the bobbin, as shown.Place the bobbin on to the thread winding spindle so the groove wil

174• Threading the lower threadCautionBefore inserting the bobbin, remove the power plug from the outlet. Not doing so could cause an injury.1Take off

18• Threading the upper threadCautionBefore threading the upper thread, remove the power plug from the outlet.Not doing so could cause an injury.1Turn

196Pass the thread between the thread guide plate and the upper thread tension dial.7Pass the thread along the groove of the thread guide plate, as th

20• Using the needle threaderCautionBefore using the needle threader, remove the power plug from the outlet.Not doing so could cause an injury.1Turn t

216Loosen the tension on the thread, and slowly return the needle threader lever forward as much as possible. After checking that the thread has passe

22• Pulling up the lower thread12Pull up the upper thread and the loop of the lower thread will come out.Pull out this lower thread.3Align the upper t

23• Application of each stitch patternCautionSewing preparationsPattern selection dialPattern selection dial No.Stitch length dial(recommend setting)S

24Pattern selection dial No.Stitch ApplicationMODELmodel 34 model 26AA-KReinforced straight stitch(left side){{BA-KReinforced straight stitch(center){

252• Changing the presser footCautionBefore changing the presser foot, remove the power plug from the outlet. Not doing so could cause an injury.Remov

26Installation1Position the presser foot pin directly below the groove in the presser foot holder.2Lower the presser foot lever to attach the presser

272• Changing the needleCautionBefore changing the needle, remove the power plug from the outlet. Not doing so could cause an injury.Be sure to dispos

28• Relationship between the needle, thread and fabric, and adjusting the thread tensionThe quality of the sewing fi nish will improve if the needle

29• Straight stitching and reverse sewingCautionStraight stitch132Position the fabric under the presser foot, and then lower the presser foot lever.St

Contents Before use• Important safety instructions ...4• How to change the power plug ...

30Thread cutter on the presser barLine up the two threads, and then cut them with the thread cutter on the presser bar.Reverse sewing is performed whi

31Sewing thick fabricWhen sewing thick fabric from the edge, the presser foot may tilt and be unable to feed through the fabric.Fabric or thick paperS

32Sewing tube-shaped fabrics1Pull out the extension table (accessory box) in the direction of the arrow.2Sew tube-shaped fabrics such as trousers or s

3314 1512• Zigzag sewingThere are various zigzag applications, such as applique and overcasting.3Position the fabric under the presser foot,

34• Adjusting thread tensionUpper thread is tightWrongsideRightsideUpper thread is looseUpper thread is looseUpper thread is tightAdjustment method fo

35• Buttonhole sewingCautionBefore changing the presser foot, remove the power plug from the outlet. Not doing so could cause an injury.Buttonhole sew

367456Raise the needle to the highest position, set the pattern dial to “4”, and sew 5 to 6 bar-tack stitches.Raise the needle to the highest position

378CautionUse the buttonhole cutter to cut the center, making sure not to cut the stitches.Note: If a marking pin is put in the bar-tack area it help

3810 15• OvercastingThis is a sewing method that prevents unraveling at the edge of the fabric.1Zigzag sewing foot2Right needle entry pointR

39• Zipper insertionCautionBefore changing the presser foot, remove the power plug from the outlet.Not doing so could cause an injury.6Attach the zipp

4Do not operate where aerosol ( spray ) products are being used or where oxygen is being administered.Doing so could cause a fi re.Use an AC 220 to 240

404Sew until just before the presser foot makes contact with the slider, and then stop the sewing machine. 5Turn the handwheel towards yourself to lo

4112• Blind hem stitchingIn this sewing method the stitch cannot be seen on the front of the fabric.Fold back the cloth so that the folded area protru

42534Position the fabric so that the needle slightly catches the fold when the needle moves to the left. Lower the presser foot and start sewing. The

43Balanced stitchesSmall stitches evenly located on right side.Needle catches too muchon the foldLarge stitches on right side.Needle does not catch on

44Pattern selection dial No.Stitch length dialStitchMODELmodel 34 model 26LL-S{-ML-S{-NL-S{-OL-S{-PL-S{-QL-S{-RL-S{-SL-S{-• Stretch & Decoration s

452• Feed dog and hook maintenanceIf the sewing machine makes a loud noise or rotates slowly, or there could be thread waste or dust in the hook or fe

463Attaching the Bobbin Case1Insert the bobbin case from the front.The red mark a on the bobbin case should be in the position, as shown in the diagra

474• Changing light bulbWarningBefore changing the light bulb, remove the power plug from the outlet and wait until the bulb cools. Not doing so could

48• TroubleshootingWhat is the problem? Check the following possibilities before contacting the service center for repair.Trouble Cause Countermeasu

49If the above treatments do not solve the problem, contact the service center as described in your warranty.When calling for service, please note the

5Do not repair, disassemble or modify except what is mentioned in the instruction manual.Doing so could cause an electric shock, a fi re or an injury.D

50• Safety precaution about the batteryWarningCautionIf the alkaline solution from the battery get in the eyes or come into contact with the skin or c

51We are committed to the protection of the environment. We strive to minimize the environmental impact of our products by continuously improving prod

679111-DEA10-B Web: www.home-sewing.com Head Offi ce Avenue de l’Industrie 21, Parc Industriel, 1420 Braine-L’Alleud BELGIUM TEL: +32 (0) 2 387

6• How to change the power plug When you change the power plug or cord, do not repair, disassemble or modify except at the authorised dealer or servic

7• Memo

8• Part names• External appearance may differ from model to model.Ú Depending on the sewing machine you have, some functions may not be applied.The m

9HandwheelThread winding switchTerminal boxThread winding spindleButtonhole adjustment screwPresser foot leverFoot controllerHollow for carryingBatter